cross-posted from: https://l.antiope.link/post/43914
Hi all. I’m trying to choose a configuration for my home storage. Speed is not a priority, I want a balance of stability and performance. I was thinking of making a raid 6 array with an ext4 file system for 4 disks of 2 TB each. Asking for advice, will this configuration be optimal?
Note - I am going to make a raid array based on external usb drives, which I will plug into the orange pi
Are you buying the hardware for this setup, or do you already have it laying around? If you don’t have the hardware yet I’d recommend not using external USB drives in any way possible, as speed and reliability will be hindered.
If you already have the hardware and want to use it I’m not super confident on recommending anything given my inexperience with this sort of setup, but I would probably try to use ZFS to minimize any potential read/write issues with dodgy USB connections. ZFS checksums files several times in transit, and will automatically repair and maintain them even if the drive gives you the wrong data. ZFS will probably be cranky when used with USB drives but it should still be possible. If you’re already planning on a RAID6 you could use a RAIDZ2 for a roughly equivalent ZFS option, or a double mirror layout for increased speed and IOPS. A RAIDZ2 is probably more resistant against disk failures since you can lose any 2 disks without pool failure, whereas with a double mirror the wrong 2 disks failing can cause a pool failure. The traditional gripe about RAIDZ’s longer rebuild times being vulnerable periods of failure are not relevant when your disks are only 2TB. Note you’ll likely want to limit ZFS’s ARC size if you’re pressed for memory on the Orange Pi, as it will try to use a lot of your memory to improve I/O efficiency by default. It should automatically release this memory if anything else needs it but it’s not always perfect.
Another option you may consider is SnapRAID+MergerFS, which can be built in a pseudo-RAID5 or RAID6 fashion with 1 or 2 parity drives, but parity calculation is not real time and you have to explicitly schedule parity syncs (aka if a data disk fails, anything changed before your last sync will be vulnerable). You can use any filesystems you want underneath this setup, so XFS/Ext4/BTRFS are all viable options. This sort of setup doesn’t have ZFS’s licensing baggage and might be easier to set up on an Orange Pi, depending on what distro you’re running. One small benefit of this setup is that you can pull the disks at any time and files will be intact (there is no striping). If a catastrophic pool failure happens, your remaining disks will still have readable data for the files that they are responsible for.
In terms of performance: ZFS double mirror > ZFS RAIDZ2 > SnapRAID+MergerFS (only runs at the speed of the disk that has the file).
In terms of stability: ZFS RAIDZ2 >= ZFS double mirror > SnapRAID+MergerFS (lacks obsessive checksumming and parity is not realtime).
Thank you! By the way, I’ve heard that ZFS has some issues with growing raid array. Is it true?
Yes very much so. You’ll need to figure out what your strategy is for array growth before you start building, because ZFS is very inflexible when growing. I normally just use mirrors because you can add 2 disks at a time with no hassles or gotchas. If you use a RAIDZ variant you will basically have to destruct and rebuild the pool/vdev if you want to grow them (or buy a whole bunch of new disks to start a separate RAIDZ array). The only other option is to replace every single disk in the RAIDZ with a larger capacity, which also works. RAIDZ expansion as a feature has been promised for many years (and the code is even already written!) but so far it has not been mainlined and although the current plan is to expect it sometime in the next year or so, that has also been the plan for the past 3-5 years. If you want to count on this feature being implemented by the time you want to grow you can feel free to do so, but it’s not something I would count on until it’s there.
If you want to be able to grow, check out mergerfs and snapraid. If you’re wanting to use a pi and USB drives it’s probably more what you’re wanting than zfs and raid arrays. It’s what i’m using and I’ve been really happy with it.