I have a 4TB HDD that I use to store music, films, images, and text files. I have a 250GB SDD that I use to install my OS and video games. So far I didn’t have any problem with this setup, obviously it’s a bit slower when it reads the HDD but nothing too serious, but lately it’s gotten way worse, where it just lags too much when I try to access files on that disk, and specially when it comes to listening to music, it’s super annoying. I’m using Elisa music player and it just takes ages to load the albums.
Below is my system and HDD information. I think I’m supposed to use hardlinks or something to access those files, could that be a reason? I’ve never even fully filled my HDD and it’s only 3 years old.
System Details Report
Report details
Hardware Information:
- Hardware Model: ASUSTeK COMPUTER INC. PRIME A320M-K
- Memory: 16.0 GiB
- Processor: AMD Ryzen™ 5 5600G with Radeon™ Graphics × 12
- Graphics: AMD Radeon™ Graphics
- Disk Capacity: 4.2 TB
Software Information:
- Firmware Version: 6042
- OS Name: Fedora Linux 39 (Workstation Edition)
- OS Build: (null)
- OS Type: 64-bit
- GNOME Version: 45.5
- Windowing System: Wayland
- Kernel Version: Linux 6.7.11-200.fc39.x86_64
You are viewing a single thread.
View all comments 2 points
*
Check its SMART: smartctl -a /dev/sdb.
2 points
It’s a bit long but here it is.
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.7.11-200.fc39.x86_64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba X300
Device Model: TOSHIBA HDWE140
Serial Number: 41IUK67JFBRG
LU WWN Device Id: 5 000039 abc58066c
Firmware Version: FP1R
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database 7.3/5528
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Apr 13 17:09:03 2024 -03
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 481) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 464
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 11263
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 073 073 000 Old_age Always - 11051
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 11259
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 8
192 Power-Off_Retract_Count 0x0032 083 083 000 Old_age Always - 8637
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 11332
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 38 (Min/Max 16/59)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 073 073 000 Old_age Always - 11003
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 545
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more
2 points
Everything seems ok. It is unlikely that the disk itself is dying. Maybe the problem is a bad cable or bus controller. Or something is wrong with the filesystem.
2 points
