Tesla is facing issues with the bare metal construction of the Cybertruck, which Elon Musk warned was as tricky to do as making Lego bricks
It’s almost like he hears about how bad the build quality of Tesla cars have become, so he thinks the solution is more accurrate, more expensive parts. Kind of like he has absolutely no clue what he’s doing, and doesn’t want to listen to smarter people telling him what they need.
I think we should rename that effect after the man who invented it: the Musk-Dunning-Kruger effect
Seriously. He can’t NOT publicly repeat every technical term that he hears, usually with next to no actual understanding.
I think it’s more likely that he is looking for excuses for the years of delays on the cyber truck.
Now he can blame it on his “desire for perfection” instead of admitting that his timeline was never viable
The design isn’t viable. They could have developed a new car in less time if it wasn’t going to be an absolute nightmare to produce reliably.
Let’s not forget about the new Roadster that was due to enter production 3 years ago.
Everyone that bought one gave Tesla a $250k interest-free loan.
This is all starting to seem intentional.
Tesla should mill the car from one solid block of steel.
Only if you also grab a Heineken for on the road on your bike ride home from the bar
Honestly, making the body from 1/4 inch think plates of steel would fix a lot of issues. It would weigh a lot, but it would be stiff.
10 microns is .4 thou, about the width of a cotton fiber. Its possible to machine those tolerances, but very time consuming as machine maintainance steps up. Its also small enough that the thermal expansion of the sheets will be larger than that
So basically elon would rather dump money into expensive equipment to improve build quality than do the thing that’s actually needed to improve build quality and pay his workers what their work is worth and make their factory environment safer?
This is the kind of petty angry bullshit you have to do to be a billionaire. Its not about being smart, it’s about on some level hating everyone that isn’t you
Making a lot of assumptions about what he’s willing to put into this.
He’s not going to get fancy expensive new equipment, he’s not going to hire the best machinists, he’s not going to slow the work down to allow that kind of accuracy. He’s going to bluster and shout and make demands without providing any way of actually achieving those demands. That’s what Elon does. He’s not an Engineer, he doesn’t design things, he doesn’t build things, he tells people who actually know what they’re doing to build something. Here, he’s just saying “Do better” without anything more, and expecting that to be enough because he doesn’t actually know shit about dick.
Frankly the closest I’ve seen to evidence that Elon has ever actually designed anything is the eyesore that is the Cybertruck, because it absolutely looks like something that cretin would draw in crayon and demand be made a reality.
It’s design demonstrates a fundamental misunderstanding of what trucks are for. I know people give the CEO of Ford shit for saying hes not worried about the Cybertruck because people who want to do real work wouldn’t take any interest in it, but its true. Trucks all have the shape of bed they do for a reason. Convergent product evolution landed on that as the best shape for a bed for trailer hitches
Reminds me of Bill Burr https://youtu.be/E3s-qZsjK8I?si=YKykzYsFt7lnPC6g
You aren’t going to hit that tolerance consistently on an assembly line no matter how much you pay. Can be done by a skilled machinist, but there are too many dynamical variables in an assembly line environment, like the previously mentioned thermal expansion.
For reference, in working with parts that interface directly with optical components about the tightest I’m ever comfortable specifying at production volumes is 0.05mm and that is for very specific dimensions and not entire parts yet he is demanding 5 times lower tolerances here.
What I meant is that Elon has set a fairly un-achievable standard, as the sheet metal parts he is talking about will grow and shrink by more than that depending on weather. Additionaly, the small parts can be machined to that tolerance, but only by a skilled machinist and not at assembly line levels.
Besides just thermal expansion, which will totally happen by driving on the road, the rotation of the motors and the use of brakes.
It will also flex as it hits bumps and takes turns.
And these will be different metals. With different thicknesses which will expand and contract at different rates.
Which just shows he has no idea how tolerances work. Small machined parts have different tolerances than large stamped parts. The key is setting the right tolerances for each part, designing the vehicle for desired gaps with those tolerances, and continuous improvement to fix and design out issues.
0.4 thou = 0.4 mil
(TIL about thous, all my engineering textbooks referencing US units must be old or something)
Imagine measuring door panels on a granite block in a climate controlled room, and sending it off to the surface grinder for rework. 🤣 Or sending the frame off to get scraped. Truly, this is the most idiotic idea on the planet and it’s all because he didn’t care about tolerances early on. His self own has turned into whatever the hell this crap was.
If LEGO and soda cans, which are very low cost, can do this, so can we.
This man is a certifiable idiot, and I feel bad for anyone working for him.
I mean, to be fair, he’s not entirely wrong, you can get that accuracy on larger parts given sufficient time, materials, tools, expertise, etc.
But a car has more parts than a Lego brick
Yeah anything is possible with enough time and money, it’s just that is about the most textbook example of comparing apples to oranges I’ve seen IRL.
Also, I suppose Lego bricks might be considered low cost if you’re a billionaire, but in the grand scheme of molded plastics they are very much a premium product.
What happens when you put that large metal part in the sun? He is entirely wrong.
Well, of course. It doesn’t change my statement though.
And the guys down the lab could go “well, we don’t have to make it out of metal.” And then it starts a rabbit hole of further insane requests that are technically possible, but to people unfamiliar with engineering (Elon) say “damn the cost” betting (incorrectly) that the time or financial cost to fulfill the requests is still profitable.
Happens to a lot of products, unfortunately. People making demands are better off knowing what the demand entails. When they do not, this is what we get.
He’s also probably confusing his experience with Space-X too. He can’t think critically, and it’s going to be his undoing. I hope at least.
He’s probably hyper self conscious about people ripping into Teslas over their clearances (with inconsistencies measured in millimetres). But, no, instead of saying “VW can produce stuff that doesn’t look like it fell from a truck and you will figure it out, too” he’s going overboard.
If we’re going overboard, why bother with cars at all? Just use this cheesy blueprint, make it work and solve all of humanity’s problems! This is what California should invest in instead of trains.
Micron, as in 0.00004"? Yes you COULD hold it, with second ops and temp control.
The total tolerance is .0004". In equally disposed bilateral tolerancing it will be ±.0002".